top of page

Part 1: Mailbox Dock Installation Instructions

​Read Before You Get Started 

​

⚠ Safety Warnings

  • Call before you dig – Always contact your local utility service to mark underground lines before digging.

  • Work safely near roads – Have someone watch for traffic if you’re installing near a roadway.

  • Follow local codes – Check with your local municipality for any regulations on mailbox installation.

​

Tools & Materials Needed:
✔️ Shovel or post-hole digger
✔️ Level
✔️ Concrete mix
✔️ Mixing container & tool
✔️ Water

 

Installation Instructions


Step 1: Dig the Hole

  • Dig a hole with a minimum diameter of 8 inches.

  • The hole should be at least 36 inches deep for stability.


Step 2: Prepare the Concrete

  • Mix the appropriate amount of concrete according to the manufacturer’s instructions.

  • Ensure the mix has the right consistency before pouring.


Step 3: Fill the Hole

  • Pour the mixed concrete into the hole until it is level with the ground surface.

​

Step 4: Install the Mailbox Dock (MBD)

  • While the concrete is still wet, gently press the Mailbox Dock (MBD) docking plate down into the concrete.

  • The top flat portion of the MBD should be flush with the surface of the concrete.

  • As you lower the MBD, use a level to check and maintain level positioning in all directions.

  • Failure to level the MBD properly may result in a crooked mailbox.


Step 5: Let the Concrete Set

  • Allow the concrete to fully harden and cure according to the instructions on the bag before placing your mailbox on the dock.


Step 6: Attach the Mailbox Post

  • Once the concrete has fully cured, place a mailbox post with an MBD magnet secured to the bottom onto the metal plate.

  • The strong magnetic connection will hold the post securely in place while allowing for easy repositioning if needed.

​

Move on to Part 2 ↴

Mailbox Dock Assembly & 

Installation Instructions

Part 2: Mailbox Dock Post & Magnet Assembly Instructions

​Read Before You Get Started 

​

⚠ Safety Warnings

  • Keep away from vehicles and metal objects – The strong magnet can attract metal suddenly, causing injury or damage.

  • Watch your fingers! – The magnet’s force can pinch fingers if placed too close to metal surfaces.

  • Keep out of reach of children – This is not a toy. Improper handling can cause injury.

  • Store safely when not in use – Keep the magnet away from electronics, credit cards, and pacemakers.​

 

Tools & Materials Needed:

​

✔️ Drill with a 5/8-inch drill bit
✔️ Measuring tape
✔️ Pencil or marker
✔️ Screwdriver
✔️ Wrench
✔️ Four long screws (included)
✔️ Carrying handle & two screws (included)

​

​

Assembly Instructions​​
​

Step 1: Mark the Center of the Post

  • Lay the 4x4 post flat and mark an X on the bottom by drawing diagonal lines from corner to corner.

  • The center of the X is where the magnet bracket will be installed.

​

Step 2: Drill the Mounting Hole

  • Using a 5/8-inch drill bit, drill a 5/8-inch deep hole at the center of the X.

​

Step 3: Attach the Magnet Bracket

  • Remove the magnet and mounting plate from the Styrofoam shipping material.

  • Align the hole on the bottom of the 4x4 post with the nut on the back of the magnet bracket.

  • Secure the mounting plate by driving four screws through the four mounting plate holes into the post.

​

Step 4: Find the Balance Point & Attach the Handle

  • Balance the entire mailbox post with the magnet attached across a teeter-totter, chair, or similar object to find the center balancing point.

  • Mark the center of the balance point with a pencil.

  • Position the center of the carrying handle over the mark and secure it with the two provided screws.

​

Step 5: Attach the Post to the Mailbox Dock

  • Gently place the magnet onto the MBD system at a 45° angle.

  • Slowly stand the mailbox post upright, allowing the magnet to fully engage with the metal plate.

​

bottom of page